Witam wszystkich.
Jest to moj pierwszy post na forum wiec prosze o wyrozumialosc:)
Od dzis popoludnia jestem szczesliwym posiadaczem linuxa suse10.2 i niestety nie moge sie polaczyc z netem. Stale lacze przez kabelek. Podaje szczegoly:
wynik
eth0 Link encap:Ethernet HWaddr 00:16:36:02:BF:34
inet addr:192.168.0.xxx Bcast:255.255.255.255 Mask:255.255.255.0
inet6 addr: fe80::216:36ff:fe02:bf34/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:20892 errors:0 dropped:0 overruns:0 frame:0
TX packets:21 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1496648 (1.4 Mb) TX bytes:1898 (1.8 Kb)
Interrupt:169 Base address:0x1800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:15 errors:0 dropped:0 overruns:0 frame:0
TX packets:15 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1111 (1.0 Kb) TX bytes:1111 (1.0 Kb)
Widac ze sieciowka ma przyznany ip,maske. Widac rowniez ze pakiety RX sa przyjmowane, niestety pakiety TX sa wysylane ale wydaje mi sie ze malo??
Nastepne podejzenie:
wynik:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.0.0 * 255.255.255.0 U 0 0 0 eth0
loopback * 255.0.0.0 U 0 0 0 lo
default 192.168.1.1 0.0.0.0 UG 0 0 0 eth0
default linux-dam.site 0.0.0.0 UG 0 0 0 eth0
Oba polaczenia default zostaly dopisane recznie za pomoca:route add default gw xxx.xxxx.x.x. Nie bylo nadanej bramki. Moze to tu tkwi problem??
P.S. jakie jest polecenie usuniecia wpisanych bram??
Ostatni problem to:
wynik:
### BEGIN INFO
#
# Modified_by: NetworkManager
# Process: /usr/bin/NetworkManager
# Process_id: 2782
#
### END INFO
Nie ma serwera DNS:( Niestety nie wiem jak go mozna recznie wpisac??
Na koniec
wynik:
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 760/M760 Host (rev 03)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SG86C202
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS963 [MuTIOL Media IO] (rev 25)
00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2 SMBus Controller
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE]
00:02.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem Controller (rev a0)
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] AC'97 Sound Controller (rev a0)
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f)
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f)
00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 91)
00:06.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02)
00:0b.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 661/741/760 PCI/AGP or 662/761Gx PCIE VGA Display Adapter
Na tym koncze mojego pierwszego ale dosc dlugiego posta. Mam nadzieje ze wszystko dobrze opisalem. Czekam na porady.
Pozdrawiam
