openSuSE
Username:
Password:
Linki sponsorowane: | inwestycje | erasmus in warsaw
Strony: [1]
  Drukuj  
Autor Wątek: karta Huawei E620,bcm4318 problem z konfiguracją SuSE10.1  (Przeczytany 4335 razy)
0 użytkowników i 1 Gość przegląda ten wątek.
gery_gery
*
Offline Offline

Wiadomości: 2


« : Grudzień 28, 2007, 17:34:13 »

Po uruchomieniu systemu dioda na karcie miga czyli działa,ale nie można nawiązać połączenia.
Starałem się coś znaleźć w sieci i natknąłem się na ten wątekhttp://forum.suse.pl/index.php/topic,15123.0.html (http://forum.suse.pl/index.php/topic,15123.0.html)
nie mogłem zainstalować pliku:bcm43xx-fwcutter,gdyż tak owego nie znalazłem dla 10.1,
ale zainstalowałem plik:bcm43xxfirmware i niestety to nie pomogło.
W kolejnym artykule na SuSEk.info jest artykuł http://www.susek.info/article/SuSE_i_Wi_Fi.shtml (http://www.susek.info/article/SuSE_i_Wi_Fi.shtml).Po spełnieniu wszystkich poleceń i użyciu tej komendy:ndiswrapper -i /home/użytkownik/WinXP/DRIVER.INF
otrzymuję ten oto komunikat:

Usage:ndiswrapper OPTION
Manage ndis drivers for ndiswrapper.
-i inffile Install driver described by'inffile'
-e driver Remove'driver'
-l List installed drivers
-m Write configuration for modprobe

wher 'devid' is either PCIID or USBID of the form XXXX:XXXX

Niestety nie wiem co dalej(jestem zielony)co zrobić jakiej komendy użyć aby poszło dalej.
Dzięki za rady i pomoc.
« Ostatnia zmiana: Grudzień 28, 2007, 17:35:49 wysłane przez gery_gery » Zapisane
gery_gery
*
Offline Offline

Wiadomości: 2


« Odpowiedz #1 : Luty 13, 2008, 21:51:30 »

Sprawdziłem czy system widzi modem i jest ok,ale jest coś nie tak.
Modem jest:
Kod:
usb 4-1: new full speed USB device using ohci_hcd and address 2
usb 4-1: new device found, idVendor=12d1, idProduct=1001
usb 4-1: new device strings: Mfr=1, Product=2, SerialNumber=4
usb 4-1: Product: HUAWEI Mobile
usb 4-1: Manufacturer: HUAWEI Technologies
usb 4-1: SerialNumber: HUAWEI DEVICE
usb 4-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
option 4-1:1.0: GSM modem (1-port) converter detected

Nie wklejałem wszystkiego bo jest jeszcze tego z 2 kartki A4 ,jest jakiś błąd:

SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
eth0: Media Link Off
ADDRCONF(NETDEV_UP): eth0: link is not ready
bcm43xx: Error: Microcode "bcm43xx_microcode5.fw" not available or load failed.
bcm43xx: core_up for active 802.11 core failed (-2)
 
Ściągnąłem i zainstalowałem "bcm43xx_microcode5.fw i oto efekt(komenda dmseg w konsoli):

bcm43xx: Radio turned on
bcm43xx: Radio disabled by hardware
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1489:bcm43xx_find_lopair()
bcm43xx: WARNING: Writing invalid LOpair (low: -9, high: 0, index: 109)
[<f8ffd9ef>] bcm43xx_phy_lo_adjust+0x1eb/0x20f [bcm43xx]

Coś  nie tak(warning). I użyłem komendy sudo wvdialconf  (konsola sudo wvdialconf) i oto wynik:
Kod:
sudo wvdialconf
Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

Modem Port Scan<*1>: Scanning ttyUSB0 first, /dev/modem is a link to it.
WvModem<*1>: Cannot get information for serial port.
ttyUSB0<*1>: ATQ0 V1 E1 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyUSB0<*1>: Modem Identifier: ATI -- Manufacturer: HUAWEI TECHNOLOGIES CO., LTD.
ttyUSB0<*1>: Speed 4800: AT -- OK
ttyUSB0<*1>: Speed 9600: AT -- OK
ttyUSB0<*1>: Speed 19200: AT -- OK
ttyUSB0<*1>: Speed 38400: AT -- OK
ttyUSB0<*1>: Speed 57600: AT -- OK
ttyUSB0<*1>: Speed 115200: AT -- OK
ttyUSB0<*1>: Speed 230400: AT -- OK
ttyUSB0<*1>: Speed 460800: AT -- OK
ttyUSB0<*1>: Max speed is 460800; that should be safe.
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
Modem Port Scan<*1>: S1   S2   S3
ttyS4<Info>: No such device or address
Modem Port Scan<*1>: S4
ttyS5<Info>: No such device or address
Modem Port Scan<*1>: S5
ttyS6<Info>: No such device or address
Modem Port Scan<*1>: S6
ttyS7<Info>: No such device or address
Modem Port Scan<*1>: S7
WvModem<*1>: Cannot get information for serial port.
ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyUSB1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
WvModem<*1>: Cannot get information for serial port.
ttyUSB2<*1>: ATQ0 V1 E1 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyUSB2<*1>: Modem Identifier: ATI -- Manufacturer: HUAWEI TECHNOLOGIES CO., LTD.
ttyUSB2<*1>: Speed 4800: AT -- OK
ttyUSB2<*1>: Speed 9600: AT -- OK
ttyUSB2<*1>: Speed 19200: AT -- OK
ttyUSB2<*1>: Speed 38400: AT -- OK
ttyUSB2<*1>: Speed 57600: AT -- OK
ttyUSB2<*1>: Speed 115200: AT -- OK
ttyUSB2<*1>: Speed 230400: AT -- OK
ttyUSB2<*1>: Speed 460800: AT -- OK
ttyUSB2<*1>: Max speed is 460800; that should be safe.
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK

Found a modem on /dev/ttyUSB0, using link /dev/modem in config.
Modem configuration written to /etc/wvdial.conf.
ttyUSB0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
ttyUSB2<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
No i niby wszystko ok,przystąpiłem do konfiguracji połączenia z internetem i jest problem.Próba połączenia kończy się komunikatem iż:Nie można utworzyć pliku blokowania modemu.I co dalej.
« Ostatnia zmiana: Luty 19, 2008, 18:01:23 wysłane przez gery_gery » Zapisane
Strony: [1]
  Drukuj  
 
Skocz do:  

erasmus - serwis komputerowy lubin - projektowanie stron lubin - cuprum lubin - projektowanie stron - zaproszenia lockerz - notatki studenckie
Template modified by designworld.pl